Date: Sat, 1 Aug 2015 21:37:36 -1000
Reply-To: "SDF ( aka ;jim lahey' - Scott )" <scottdaniel@TURBOVANS.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: "SDF ( aka ;jim lahey' - Scott )" <scottdaniel@TURBOVANS.COM>
Organization: Cosmic Reminders
Subject: Re: What is it?
In-Reply-To: <CAB2Rwfh2-abXtew99qPEsjCzQdaWJFgpNh662wKbqphPu4ETsg@mail.gmail.com>
Content-Type: text/plain; charset=utf-8; format=flowed
all screw-type hose clamps need a snugging up a while after being newly
installed.
And then periodically....once a year at least. Not 'mash things' ..just
nicely tight but not too much. The hose wants a little more clamp
pressure after a while.
Can't have no fuel pressure regulator banging and swinging around , or
able to, in any decent installation or configuration.
It does matter.
Flex, the frequencies and dynamics of those flexings, and vibration,
etc............. all need to be managed and looked after on all wire
and hose systems, on all vehicles..if ya want it safe and reliable.
Have you seen a positive battery cable rub against an oil filer for
5,000 miles ? ..and what that can do ?
( it can happen on a stock diesel vanagon if ONE plastic clip on that
battery cable is not there ( super dumb VW ! ..a fire waiting to happen ).
Yep ...[psitive battery cable rubbed against ) the conveniently
located oil filter _ , until it zapped through, lighting the hot oil in
the oil filter and thus engine on fire.
That vehicle is where I really learned the value of managing vibration
and rubbing contact situations, especially around and on the engine.
On 8/1/2015 8:52 PM, Neil N wrote:
> Thanks for identifying that partial yellow ring Scott.
> Interesting details!
> I didn't really think it "played into" the cause of the OP's fuel leak
> but thought I'd ask of it.
>
> When checking injector spray pattern on my 2.1 WBX, sometime after I
> replaced ALL the fuel hoses in engine bay, simply lifting the set of 2
> injectors up and away from the driver side engine head caused a ***tiny***
> bit of fuel to seep out between the fuel rail and hose. This was obviously
> due to a slightly loose clamp.
> (much like a radiator hose clamp replacement, I should have re-checked all
> fuel hose clamps some miles after doing the fuel hose replacement job).
> Tightening that fuel hose clamp fixed the issue. I re-checked all relevant
> fuel hose clamps.
>
> @ the OP. I may be mistaken, but I don't see that fuel pressure regulator
> bolted down. Not that it matters per se, (as a fuel hose replacement job
> may be in your near future), but I'd guess that simply moving that part,
> and hoses attached to it, could have disrupted those old hoses and clamps
> enough to cause a fuel leak ??
>
> Neil.
>
>
>
>
> On Sat, Aug 1, 2015 at 11:02 PM, SDF ( aka ;jim lahey' - Scott ) <
> scottdaniel@turbovans.com> wrote:
>
>> Starting back when cars started having pretty complex emissions systems
>> ...and often Lots of vacuum hoses and devices ( you should see a pre-fuel
>> injection Calfiornia Rabbit sometime ..like 20+ vacuum hoses ) ..
>>
>> it became a Federal Requirement that all US cars have a Vacuum Diagram
>> ...under the hood, even on the underside of the hood sometimes ..
>> and little colored plastic rings like the yellow one on the Fuel Press.
>> regulator in the pic .
>>
>>
>>
>
> --
> Neil n
>
> Blog: Vanagons, Westfalia, general <http://tubaneil.blogspot.ca>
>
> 1988 Westy Images <https://picasaweb.google.com/musomuso/New1988Westy>
>
> 1981 Westfalia "Jaco" Images, technical <http://tubaneil.googlepages.com/>
>
> Vanagon-Bus VAG Gas Engine Swap Group <http://tinyurl.com/khalbay>
>
|