Date: Mon, 10 Aug 2015 20:05:35 -0400
Reply-To: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Subject: Re: Rad fan testing
In-Reply-To: <9B682855-4DF1-4D67-AC3F-569127894E45@gmail.com>
Content-Type: text/plain; charset="us-ascii"
Could be significant. On the 87 and later vans the AC system is fed off an
independent wire directly off the alternator. This also powers the radiator
fan in a low speed when the compressor is called for. There is also pressure
switch control that operates a relay in the fuse box to provide an
intermediate fan speed when the AC needs it. If that wire was left off
during the conversion along with other issues the radiator fan can be
effected.
The supper high speed fan operation is fed from a 70 amp relay mounted above
the fuse box. It has a fusible link on it. It has its own feed wire from the
battery. One of the two red with white stripe wires. That wire can fail at
the connections on both ends.
Dennis
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of
Stacy Schneider
Sent: Monday, August 10, 2015 6:13 PM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: Rad fan testing
What does a Subaru conversion have to do with the AC not being hooked up ?
Stacy
Sent from my iPhone
> On Aug 10, 2015, at 2:09 PM, Larry Alofs <lalofs@GMAIL.COM> wrote:
>
> Take another look at those diagrams. Take lots of long looks.
> You still haven't revealed what year the vehicle is.
> You will probably need to look at the separate diagram for the AC, not
> the main diagram if it a newer model, whether the AC is connected or not.
>
> Larry A.
>
>
>> On Mon, Aug 10, 2015 at 2:05 PM, Michael <mikewelldon@icloud.com> wrote:
>>
>> So far I've replaced the resistor, followed the ground to the tree
>> (looks
>> connected) and get a clicking noise from the relay when jumping the
>> plug connector.
>>
>> The AC on this van is not connected because it is a Subaru conversion.
>>
>> Do you think the clicking is a bad relay up top behind the fuse box?
>>
>> I do have the Bentley and have taken a look at the wiring diagrams,
>> but that's about it.
>>
>> Mike
>>
>>
>>> On Aug 9, 2015, at 8:12 PM, Dave Mcneely <mcneely4@COX.NET> wrote:
>>>
>>> On my radiator fan, a mechanic, a radiator shop owner, broke the
>>> post
>> where the wire connects to the motor. He didn't admit to causing the
>> fan to be bad, instead claiming that, "It's just one of those things
>> that got old and tired." It hadn't been that tired until his heavy
>> fist got hold of it. Anyway, that is another place that the fan
>> motor can fail. All it required was a simple fix of a longer post
>> and a nut to hold it in place, but he insisted that he needed to install
a new motor, which of course, he
>> wanted to charge me to do. Needless to say, that was my last visit to
>> that place. mcneely
>>>
>>> ---- Dennis Haynes <d23haynes57@HOTMAIL.COM> wrote:
>>>> Use a meter to see if power is getting to the motor. Do you have
>>>> the
>> Bentley
>>>> or another way to get the wiring diagram? What year? It is very
>>>> rare
>> for the
>>>> these motors to completely give up the ghost but the wiring,
>>>> switches,
>> and
>>>> control relays are a whole different story. On the early vans the
>>>> common failures beside the radiator switch are the fuse, fuse box,
>>>> relay for
>> high
>>>> speed and wiring. On the later vans add the fusible link, resistor
>> behind
>>>> the headlight, wiring to the air conditioner, and there are two
>> relays, one
>>>> on the fuse box and one mounted above it.
>>>>
>>>> Dennis
>>>>
>>>>
>>>> -----Original Message-----
>>>> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On
>> Behalf Of
>>>> Michael
>>>> Sent: Sunday, August 9, 2015 7:37 PM
>>>> To: vanagon@GERRY.VANAGON.COM
>>>> Subject: Rad fan testing
>>>>
>>>> Hi everyone,
>>>>
>>>> I hear people talking about hooking a battery up to the radiator
>>>> fan in order to test it.
>>>>
>>>> Never done it. Any ideas on the best way?
>>>>
>>>> Jumping the connector doesn't work, the ground looks like it's
>> connected to
>>>> the ground tree behind the fuse panel...now I'm trying to figure
>>>> out if
>> it's
>>>> just the motor.
>>>>
>>>> Mike
>>>
>>> --
>>> David McNeely
>>
|