Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (August 2015, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 15 Aug 2015 11:12:00 -0400
Reply-To:     Edward Maglott <emaglott3@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Edward Maglott <emaglott3@GMAIL.COM>
Subject:      Re: Supporting the pop top to remove the frame
Comments: To: PB <pbrattan@gmail.com>
In-Reply-To:  <CAOBs5F5DQyzhwYcc=CwvS72mweqaRaT6n3JUWwxRt6EJUsTELA@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8

If you put your stick in the center of the front so it braces against the mechanism that latches the poptop in the down position the weight will be nicely distributed. The fiberglass top is really sturdy anyway but that latch mechanism is designed to distribute the force that holds the top closed to the fiberglass. Good luck! Edward

On Fri, Aug 14, 2015 at 6:42 PM, PB <pbrattan@gmail.com> wrote:

> Edward, I forgot about those hinges at the back! That, along with the 2 x > 4 would form a fairly stable triangle, but wouldn't the 2 by 4 stress that > one point of the poptop? > Patti > > On Fri, Aug 14, 2015 at 2:26 PM, Jeff Stewart <fonman4277@comcast.net> > wrote: > > > > > > > No, I've used a tall cardboard box to support mine while replacing > canvas. > > > > > > Sent from my Verizon Wireless 4G LTE smartphone > > > > -------- Original message -------- > > From: Edward Maglott <emaglott3@GMAIL.COM> > > Date: 08/14/2015 5:23 PM (GMT-05:00) > > To: vanagon@GERRY.VANAGON.COM > > Subject: Re: Supporting the pop top to remove the frame > > > > I think a "stick" would do it just fine. a piece of 2x4 you could get > cut > > to length at the DIY bldg supply store, or maybe you have something > laying > > around? The hinges at the back of the van should keep it from skewing > left > > or right. Am I "under-thinking" this too much? > > Edward > > > > On Fri, Aug 14, 2015 at 4:57 PM, PB <pbrattan@gmail.com> wrote: > > > > > Ok - so in order to repair or replace my pop top frame mechanism > without > > > removing the poptop itself, I would need to support it. That's a simple > > > concept, but I would like to know EXACTLY how! I'm envisioning a > wooden > > > jig something like THIS ONE > > > < > > > > > > http://s74.photobucket.com/user/edtech2000/media/Pop%20Top%20Suppport.jpg.html > > > >. > > > I was thinking that an auto jack might go below the base, but never > used > > > one. > > > > > > Harbor freight has a great little hydraulic table lift > > > < > > > > > > http://www.harborfreight.com/500-lb-capacity-hydraulic-table-cart-60730-10041.html > > > > > > > that would probably be perfect, but I'm not sure I want to lay out the > > $$$. > > > (a coupon would reduce it by $20.) > > > > > > Sometimes I get a little too complicated. I'd like to know of other > ways > > > to securely and safely prop up the pop top so that the frame can be > > > removed. Pictures would be very helpful, as I don't always understand > > the > > > terminology. > > > > > > Thanks! :-) > > > Patti > > > 90 Westy Automatic > > > Los Angeles > > > > > > *♪♫**♥**♫♪♪♫**♥**♫♪♪♫**♥**♫♪♪♫**♥**♫♪* > > > If it's not on my Smart Phone, it doesn't exist... > > > ●▬▬▬▬▬▬ஜ۩۞۩ஜ▬▬♥▬▬▬ஜ۩۞۩ஜ▬▬▬▬▬● > > > > > > > > > -- > > *♪♫**♥**♫♪♪♫**♥**♫♪♪♫**♥**♫♪♪♫**♥**♫♪* > If it's not on my Smart Phone, it doesn't exist... > ●▬▬▬▬▬▬ஜ۩۞۩ஜ▬▬♥▬▬▬ஜ۩۞۩ஜ▬▬▬▬▬● >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.