Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (January 2016, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Tue, 5 Jan 2016 18:48:32 -0700
Reply-To:     OlRivrRat <OlRivrRat@COMCAST.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         OlRivrRat <OlRivrRat@COMCAST.NET>
Subject:      Re: Transmission swap problems: 86 tranny onto 83 engine.
Comments: To: Rick Cooper <rickdcooper@GMAIL.COM>
In-Reply-To:  <CAG12aisXyDQA=c4875UDNa3c26eq2WVTvrvxNLdASyfpKeRBMA@mail.gmail.com>
Content-Type: text/plain; charset=us-ascii

Rick

I have done about A Half Dozen TranySwaps in the Past year & will Attest to the Fact that the Last 1.5 - 1 in's

Can Definitely Be The GriefZone & it Doesn't seem to Matter How Well All is LinedUp ~ I stumbled on to something many

Tranys back that has worked for Me on several occasions but unfortunately I manage to forget until I have spent way to

much time FightingTheTrany UnderTheBus ~ In Frustration I will SlideOut FromUnder & even with the Rear of the Van'

Up On Ramps Reach Over the Eng', Grab the BellHousing By Its Ears & Pull & It will Just Slide Into Place ~ Leaving Me

Scratching My Head, while maybe Heading for a Beer & saying Why Did That Work & Why The Heck Don't I Remember

That Sooner ~ It MightNot Work for a lot of folks 'cause I am Equipped With 36"Legs Plus 36"Arms ~

ORR~ DeanB

On 5 Jan , 2016, at 12:51 PM, Rick Cooper wrote:

> Thanks Dean. I'm almost certain that the throw-out bearing was fully retracted (it is now, with the tranny out and unless my helper (youngest son) reset it without mentioning it to me...), but will certainly double-check that when we try again. I can't tell you exactly how big the gap was and can't remeasure now since my son is not avail for a couple of days, but from my visual inspections yesterday, I'd guesstimate the gap at about 1.25 - 1.5 inches. > > On Tue, Jan 5, 2016 at 11:21 AM, OlRivrRat <OlRivrRat@comcast.net> wrote: > Be Sure that the ThrowOut/Release Bearing is Mounted on the Fork Properly & > > that it is Fully Retracted ~ Check that the Gap Between Eng' & BellHousing is Even > > All The Way Around ~ How Big is that Gap when You Get Stymied ? ~ > > ORR ~ DeanB > > > On 5 Jan , 2016, at 12:03 PM, Rick Cooper wrote: > > > I'm trying to replace the manual transmission in an '83 Westy with one from > > an '86 tintop. Quite simply, I can't get the transmission to mate with the > > 1.9 engine; there is some mechanical obstruction. I think I'm far enough > > away that the input shaft has not even started into the clutch disc > > splines; the fresh grease I put on the input shaft has not been disturbed. > > > > I don't think its an incompatible parts issue since they appear identical. > > The transmissions are both stamped 091 301 103D, the pressure plates are > > marked "Sachs Typ M228" and the clutch discs are both Sachs and measure > > 228mm in diameter. (The clutch kit from the 1983 is nearly new; the PO > > told me it had been recently replaced and I was hoping to re-use it.) The > > input shafts appear identical; the clutch disks from both will slide onto > > either one of them. > > > > Why was I replacing the transmission? Gearing problems -- usually > > impossible to shift into first from neutral; usually had to get van moving > > in 2nd and then downshift to 1st. Also issues shifting from 2nd to 3rd. > > It seemed less expensive to swap in a good used transmission than to have > > that one rebuilt. > > > > Can anyone suggest what the problem might be? (I haven't done many > > engine/tranny swaps, but I'm experiencing deja vu. I once tried to put the > > engine from an '88 Chev S10 into a 1991 Chev S10. Same problem; could not > > get the engine to engage with the 91 transmission's input shaft. Turns out > > that GM had changed the input shaft size in the intervening years.) > > > > Thanks, Rick > >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.