Date: Fri, 6 May 2016 15:49:02 -0400
Reply-To: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Subject: Re: Rear Brakes: E-brake lever lube,
E-brake spring function (purpose)
In-Reply-To: <CAB2RwfgiLn3u3v9c3h=2iHyyp9_fB601DXLGMumNEE75G-syaw@mail.gmail.com>
Content-Type: text/plain; charset="Windows-1252"
There are no shims on those lower anchors. With the GoWesty shoes and new drums there is no room for shims. The GoWesty HD drums are even a tighter tolerance. The silver you see there is nickel based anti-seize. Not that I also used brake grease on the pads where the shoes rest on the backing plate and where the shoes rest on the cylinders and lower mounts.
The creeper is known as "The Bone". it has large wheels that easily roll over obstructions like tools.
Dennis
> Date: Thu, 5 May 2016 22:34:18 -0700
> Subject: Re: Rear Brakes: E-brake lever lube, E-brake spring function (purpose)
> From: musomuso@gmail.com
> To: d23haynes57@hotmail.com
> CC: vanagon@gerry.vanagon.com
>
> Nice looking creeper.
> Wow. Just, wow; those backing plates have seen better days!
> I have a set of those new backing plates, 2 more on order for that rainy day.
> Nice pics of the hardware.
> Those are shims I see at lower shoe "anchors" ?
>
> One thing I forgot to mention, and I'm sure I'm not the only one to do this,
> but to remove the cable, I've used Vice Grips or large pliers to
> grab the portion of cable that butts up against the backing plate. I'm
> sure that part is designed to take some pressure
> but how much?
>
> Could an enthusiastic DIY type crush that portion enough to
> hamper cable operation?
>
> On 5/5/16, Dennis Haynes <d23haynes57@hotmail.com> wrote:
> > Here is a link to a recent rear brake overhaul. Note some important
> > details:
> > The direction and position of the adjuster bar. Yes, longer part of the fork
> > goes behind the lever and rest against the shoe.
> > The cables again get adjusted so the adjuster bar is loose (barely) between
> > the shoes being pushed by the spring loaded lever. If it doesn’t go loose
> > then the lever won’t turn the adjuster out.
> > Positon of the top springs. Upside down they can keep the star wheel from
> > turning.
> > These are GoWesty shoes. They do not need to get shimmed out on the bottom.
> >
> > These are the GoWesty heavy duty drums. They are even round!
> > The Spring kit is from Autozone. Note the hold down pins, clips, and springs
> > fit.
> > Backing plates very important. Bent twisted, weak, etc. The shoe do not
> > remain aligned with the drum. Never pry a drum off with a lever between the
> > backing plate and drum. Bad alignment, bad brake action, lost contact,
> > noise.
> >
> > Dennis
> >
> > https://onedrive.live.com/redir?resid=9B02084A888884A6!133400&authkey=!AMfmcTU_5HJVkXY&ithint=folder%2cjpg
> >
> >
> >
> >
>
> --
> Neil n
>
> Blog: Vanagons, Westfalia, general <http://tubaneil.blogspot.ca>
>
> 1988 Westy Images <https://picasaweb.google.com/musomuso/New1988Westy>
>
> 1981 Westfalia "Jaco" Images, technical <http://tubaneil.googlepages.com/>
>
> Vanagon-Bus VAG Gas Engine Swap Group <http://tinyurl.com/khalbay>
|