Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (July 2016, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 3 Jul 2016 22:45:12 -0400
Reply-To:     Dennis Haynes <d23haynes57@HOTMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Dennis Haynes <d23haynes57@HOTMAIL.COM>
Subject:      Re: My van's home again!!!
Comments: To: Marc Perdue <mcperdue@GMAIL.COM>
In-Reply-To:  <CAEwp_cR1VO+FBo3L6F4Q=Bmj40a0Ht2tOpaP1k8ChyPw2PbNxA@mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"

Somehow I would doubt that is had a bad ECU, AFM and temp 2 sensor. Also why would one keep running a rebuilt engine not "right" for 500 miles? Running rich = oil dilution and sooting up rings while they should be seating along with trashing the O2 sensor and catalytic converter. As for the oil pressure warning switch why not the correct or quality part with the engine install? Its amazing that the aftermarket can’t get this simple part right.

Dennis

-----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of Marc Perdue Sent: Sunday, July 3, 2016 3:05 PM To: vanagon@GERRY.VANAGON.COM Subject: My van's home again!!!

Hi all,

My van is back home from the shop again!!! And finally I have some good news to report! For those who have been following my saga, I had to have my engine rebuilt and it was not running right during the 500-mile break-in period. It was running rich, sometimes when I would downshift on the highway to pass (auto), a bunch of smoke would go billowing out the back, and when I would come off the highway, any time the RPMs dropped below 2500, the oil buzzer would come on. The builder had already verified that the engine had good oil pressure.

I took the van in for its 500-mile post-break-in adjustments. He replaced the oil pressure sender with one from the dealer. That problem was solved, but it still wasn't running right. Long story short, he swapped in a known good ECU and a known good AFM and replaced the Temp II sensor and the engine's running like new!

While it was there, I had him replace the shocks and upper control arm bushings too and it's handling a lot differently now. That's going to take some getting used to. It's funny how you adapt to a particular way of handling over time and when your vehicle gets fixed and handles correctly, it's like you have to learn how to drive it properly all over again. Who knew my van was actually capable of turn-in?!?

They did set the Koni shocks to a pretty soft setting and I think I want to firm that up. Anybody know how to do that?

I did make a shocking discovery about the speedo, but I'll cover that in a separate post.

Just overjoyed to have my van back home now! Marc


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.