Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (July 2016, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Tue, 26 Jul 2016 18:26:52 -0700
Reply-To:     Mark McCulley <markmcculley@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Mark McCulley <markmcculley@GMAIL.COM>
Subject:      Re: replacing transmission selector shaft seal
In-Reply-To:  <CAKbau521uRUeoBekVkQMA1QUcotR8DSNv_C=dyVV-5jLEGERpw@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8

I checked the vent tube, it's not kinked or clogged. And the transmission is not overfilled, in fact the oil level is down about 10-12mm from the bottom of the fill hole. Next step is to replace the seal. And refresh the oil while I'm at it.

-Mark

On Tue, Jul 26, 2016 at 7:01 AM, Mark McCulley <markmcculley@gmail.com> wrote:

> Thanks Dennis. I'll check the fluid level and vent tube. There's no reason > I can think of that the transmissions would overheat, still have the stock > 2.1L and don't pull a trailer. I did switch the type of oil I use a few > years back, 3 years ago I switched from Redline to Delvac and then a year > later I switched back to Redline when I installed a driveshaft decoupler. > Both oils are synthetic 75W90. The transmission has just under 200K total > miles, 80K since rebuild (I don't know if seal was replaced then or not). > > -Mark > > On Mon, Jul 25, 2016 at 7:08 PM, Dennis Haynes <d23haynes57@hotmail.com> > wrote: > >> Yes this seal is easy to replace. However its leaking is usually a >> symptom of something else going on. There is also an insert-bushing behind >> it that may be cracked. Make sure the transmission is not overfilled and >> that the vent tube is not kinked or otherwise clogged. This seal never sees >> enough action that it should wear out. For it to go bad is a sign the >> transmission has been over heating. >> >> Dennis >> >> >> -----Original Message----- >> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf >> Of Mark McCulley >> Sent: Monday, July 25, 2016 9:26 PM >> To: vanagon@GERRY.VANAGON.COM >> Subject: replacing transmission selector shaft seal >> >> My '87 has transmission oil leaking from where the selector shaft enters >> the transmission case. Is it fairly straight forward to replace the seal >> with the transmission installed? This is a syncro if it makes a difference. >> I see van-cafe has a write-up here: >> >> http://www.van-cafe.com/home/van/page_131_783/transmission-selector-shaft-seal.html >> , >> seems like it's not particularly difficult. >> >> Thanks, >> Mark >> Seattle, WA >> > >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.