Date: Thu, 5 Jan 2017 18:19:01 +0000
Reply-To: Ryan Perry <rjdperry@GMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Ryan Perry <rjdperry@GMAIL.COM>
Subject: Re: Engine Bay Zip Ties
In-Reply-To: <21A82EBD-9257-4D02-929E-D67C40DACF86@mac.com>
Content-Type: text/plain; charset=UTF-8
Not quite, these use a stud already in the engine compartment. There are 2
of them along the driver side holding wiring harness.
Grabbed a picture of them today, hopefully it makes sense. The stud goes
through the mount them you slide it over to lock it in. I'm sure it is no
problem to use a different set up, but if it's there... It's in my Artie
album, take a look.
https://goo.gl/photos/xf6kN5Pbw1kCALVC9
On Thu, Jan 5, 2017, 1:10 PM Edward V Barger <edvbarger@mac.com> wrote:
> interested also need to neat up some wire but these state tat they are for
> indoor use
>
> ed
>
>
> Edward V Barger
> edvbarger@mac.com
> 310 922 6251
>
>
>
> > On Jan 5, 2017, at 8:17 AM, OlRivrRat <OlRivrRat@COMCAST.NET> wrote:
> >
> > How about these ~
> >
> >
> http://www.ebay.com/itm/25-Push-Mount-Cable-Tie-For-Imports-200mm-Length-New-/381778290851
> >
> > More here ~
> >
> > http://www.ebay.com/bhp/push-mount-cable-ties
> >
> > ORR ~ DeanB
> >
> > On 5 Jan , 2017, at 6:01 AM, Ryan Perry wrote:
> >
> >> Took a look at both and not seeing them as they are. But, it looks like
> >> maybe the screw types could work if the hole is large enough to fit the
> >> stud in the engine compartment.
> >> Seems these would be available. I found these through an image search,
> >> about as close as I can find.
> >>
> >>
> http://www.panduit.com/en/products-and-services/products/cable-and-wire-bundling/plastic-cable-ties/plastic-cable-ties-one-piece/specialty-ties/stud-mount/PLST4HS25-TL300
> >>
> >> I will try to get a picture and measurements, see if that helps.
> >>
> >> thanks for the info!
> >> Ryan
> >>
> >> On Wed, Jan 4, 2017 at 11:22 PM <mfmagnani@sbcglobal.net> wrote:
> >>
> >>> Have you tried McMaster.com ?
> >>> Mike M
> >>>
> >>> Sent from my iPhone
> >>>
> >>>> On Jan 4, 2017, at 7:18 PM, Ryan Perry <rjdperry@GMAIL.COM> wrote:
> >>>>
> >>>> Hey everybody, Happy New year!
> >>>> If you remember a while back I had posted about my engine biting the
> >>> dust.
> >>>> We are now mid install of a spanky new GoWesty 2.2 engine. With the
> old
> >>>> engine out I am cleaning the bay and noticed the zip ties that hold
> the
> >>>> main harness around the edge of the bay have broken. They are unique
> >>> with a
> >>>> hole that allows a manufactured stud on the body to slip in and slide
> >>> over,
> >>>> then you just regular zip tie the wires. Need 2 of these, any idea
> where
> >>>> they can be sourced? Suggestions otherwise? I'm a bit of a purist so
> >>> would
> >>>> like to try and find these if they still make them. Hopefully I
> >>> described
> >>>> well enough but can grab pictures too when I get back to the shop.
> >>>> Thanks
> >>>> Ryan
> >>>> Asheville, NC
> >>>
>
|