Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (May 2017, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 4 May 2017 22:37:40 -0400
Reply-To:     David Bohannan <fjazzbass@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         David Bohannan <fjazzbass@GMAIL.COM>
Subject:      Re: 2.1 wbx Compression Test
Comments: To: Neil N <musomuso@GMAIL.COM>
In-Reply-To:  <CAB2RwfivwqSNco0yr=PCuWmjGfLRxwpQ+Sdce3A6joirF0TNnQ@mail.gmail.com>
Content-Type: text/plain; charset=us-ascii

Neil,

I just went through this with mine- compression was good on 3- one bad- blowing gases into coolant.

I retorqued the heads to no avail and wish I'd just torn down the engine long before. The gases in the coolant may have caused a lot more corrosion on my heads... if you know gases are leaking, it would be far better to tear it down now!!! Just my opinion.

I've since found a good used engine and will be rebuilding my old one- old heads look terrible and I'll be replacing with possibly new.

My main problem was that a small crack developed between a cooling passage and the mating surface of the head- tiny crack - almost a casting defect.

I drove it far too long thinking I was loosing coolant and having to bleed the system of extra air. It turns out the excessive pressure created leaks in the system and I was just bleeding gases out of the radiator....lesson learned.

YMMV

Dave 85 GL "Baby Bus" with a cheeky little used 1.9er

> On May 4, 2017, at 8:30 PM, Neil N <musomuso@GMAIL.COM> wrote: > >> On 5/4/17, Neil N <musomuso@gmail.com> wrote: >> >> As a last resort, I will check the head nuts to see if any are >> obviously loose .... > > > I should add that as per previous posts I've made about this engine, > after driven a while, the engine will blow compression gases into the > coolant. The main reason for taking a compression test is to establish > a base line though even if some loose head nuts are loose, tightening > them may not change the compression results. i.e. the cooling system > gets over pressurized after I drive the van for quite a few miles. > > Neil. > > > > -- > Neil n > > Blog: Vanagons, Westfalia, general <http://tubaneil.blogspot.ca> > > 1988 Westy Images <https://picasaweb.google.com/musomuso/New1988Westy> > > 1981 Westfalia "Jaco" Images, technical <http://tubaneil.googlepages.com/>

> > Vanagon-Bus VAG Gas Engine Swap Group <http://tinyurl.com/khalbay>


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.