Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (June 2017, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 8 Jun 2017 17:01:34 -0700
Reply-To:     Neil N <musomuso@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Neil N <musomuso@GMAIL.COM>
Subject:      Re: Distributor Shaft Pin
Comments: To: Dennis Haynes <d23haynes57@hotmail.com>
In-Reply-To:  <CY1PR20MB0029F1909D7CDFB69956A7A6A0C90@CY1PR20MB0029.namprd20.prod.outlook.com>
Content-Type: text/plain; charset="UTF-8"

Thanks Dennis.

Images of the pin I removed from the distributor in question: (ABA engine):

https://goo.gl/photos/NHMzzcH8CjxC8oNv6

https://goo.gl/photos/ZBoH5cWrX8RkrKah7

But looking back at some images of mine, I see what you mean about the Vanagon gas engine distributor pin. Image: https://goo.gl/photos/4E34mTEJcUWhq8dR8

Sorry for that mis statement folks.

For the ABA, my recollection was that one had to buy the entire distributor; there is no repair kit i.e. new pin. I have a spare distributor, this one was free, but figured I'd clean it up and see if I could find a solution for the pin.

Neil.

On 6/8/17, Dennis Haynes <d23haynes57@hotmail.com> wrote:

> On the Vanagon gas engines this pin is a solid, hardened pin. It is press > fit in the shaft and drive floats on it. This allows for the drive to slide > to take up any misalignment between the drive piece and distributor shaft. > The pick-up coil kits include a new drive pin. I can see a roll pin wearing > through and failing. My memory is hazy but I think the this distributor also > uses a solid pin. If so it is solid for a reason. If it should be a roll pin > why not get the correct one so you won’t have to worry? > > Dennis > > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of > Neil N > Sent: Thursday, June 8, 2017 5:26 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Distributor Shaft Pin > > Hi all. > > This is for a distributor from a different VW engine but Vanagon gas engines > have the same pin arrangement. -- Neil n

Blog: Vanagons, Westfalia, general <http://tubaneil.blogspot.ca>

1988 Westy Images <https://picasaweb.google.com/musomuso/New1988Westy>

1981 Westfalia "Jaco" Images, technical <http://tubaneil.googlepages.com/>

Vanagon-Bus VAG Gas Engine Swap Group <http://tinyurl.com/khalbay>


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.