Date: Wed, 6 Sep 2017 22:37:18 -0600
Reply-To: OlRivrRat <OlRivrRat@COMCAST.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: OlRivrRat <OlRivrRat@COMCAST.NET>
Subject: Re: Oil pressure light and buzzer
In-Reply-To: <951E414B-4692-4B7B-BCA6-E88F1302BFEE@shaw.ca>
Content-Type: text/plain; charset=us-ascii
Snazzy for sure ~ But ~ In any of these adaptations where the Sensors are located @ the End of a Path
(Which in most cases is Conveniently Located Above the Eng') Instead of @ a Flow By Location, how can one
be sure they are receiving Real Time Info Or Possibly Even Not Oil Info @ All but Maybe the Pressure & Temp
of a Trapped Air Pocket ~
ORR ~ DeanB
On 6 Sep , 2017, at 4:58 PM, Alistair Bell wrote:
> Hi,
>
> I made a manifold and relocated the two pressure switches plus added a pressure gauge sender. Pics etc here
>
> https://shufti.blog/2012/07/05/vanagon-oil-pressure-sender-relocation/
>
> Jeeze, been 5 years now, the set up works fine, the connections have not leaked.
>
> The pressure switch location at the rear of the engine was then used for a oil temp sender probe. And that's been working fine for same time. Mind you, accession that spot with engine in van is a chore. I did it when engine was out for head work.
>
> Alistair
>
>> On Sep 5, 2017, at 5:10 PM, David McNeely <davmcneely40@GMAIL.COM> wrote:
>>
>> Hmmm.... . Isn't pressure at the filter different from pressure at the
>> engine? Also, that sandwich, added to the factory oil cooler, plus in my
>> case the adapter for an external oil cooler, and the filter mount would be
>> getting sort of crowded.
>>
>> I added an extension onto the engine case mount for one sender, and used a
>> t-fitting to mount the gauge sender there also. The result, a gauge sender
>> that works just fine, and both low and high pressure warnings working
>> also. The original set up is not tampered with (except for putting one
>> sender on an extension to make it easier to access).
>>
>> Actually, a highly competent mechanic did this for me. I am a klutz.
>>
>> mcneely
>>
>>> On Tue, Sep 5, 2017 at 2:37 PM, OlRivrRat <OlRivrRat@comcast.net> wrote:
>>>
>>>> On 5 Sep , 2017, at 2:57 PM, Gabriel Hourtouat wrote:
>>>>
>>>> -marked the tin so that I know where to trim it so I can install a
>>> pressure
>>>> gauge.
>>>>
>>>> Any recommendations as to the pressure gauge? I see that VAN CAFE has a
>>>> nifty kit:
>>>> http://www.van-cafe.com/page_15
>>>> Anyone have any comments on that?
>>>
>>> This is a SetUp I like ~
>>>
>>> & One of these makes mounting the SendingUnits easier ~
>>>
>>> http://www.glowshiftdirect.com/oilfilter-sender-adapter-3-4unf-16.aspx
>>>
>>> http://prosportgauges.com/oil-filter-adaptor-plate.aspx
>>>
>>>
>>> Gauges
>>>
>>> http://www.glowshiftdirect.com/Gauges.aspx
>>>
>>> http://www.glowshiftdirect.com/MaxTow-Oil-Pressure-
>>> Gauges.aspx?sitelink=LeftNav
>>>
>>> http://www.glowshiftdirect.com/MaxTow-Oil-Temperature-
>>> Gauges.aspx?sitelink=LeftNav
>>>
>>> & if You choose these, order Extra Wire for Each due to Van'Length
>>> ~
>>>
>>>
>>> Or ~
>>>
>>> http://prosportgauges.com/52mm_digital_series_gauges.aspx
>>>
>>>
>>>> Dual gauge pod for ash tray
>>>
>>>> http://www.t3technique.com/electrical/dual-gauge-pod.html
>>>
>>> ORR ~ DeanB
|