Yes, the ICM is gone but the valve is retained. Has to be some way to introduce bypass air to control idle, it's not done with the throttle plate like the old days. So, everything is replaced except the fuel pump and restrictor, idle air valve, temp and coolant sensors, and fuel injectors. Nice things are added like a custom ECU, knock sensor, crank position sensor, MAP (manifold absolute pressure) sensor, new waterproof connectors, and sealed relays. There is really nothing more you need to replace, this system will keep the engine running at maximum efficiency in all conditions and elevations. You have to give them credit, they will not give up on the WBX. Not yet at least, but at some point it's not going to be cost effective, and your favorite VW shop will not be able to work on this engine management system either. Stuart -----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of Dennis Haynes Sent: Thursday, January 4, 2018 11:37 AM To: vanagon@GERRY.VANAGON.COM Subject: Re: Engine thoughts--now Go Westy engine management system I think the idle control module goes, the valve is still used. In my experience the valves only when folks do stupid stuff or they get filled with engine oil after a burned piston. Dennis -----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of Neil N Sent: Thursday, January 4, 2018 2:18 PM To: vanagon@GERRY.VANAGON.COM Subject: Re: Engine thoughts--now Go Westy engine management system i think GW mentions this on their web page but the WBX 2.1 idle control unit would be deleted. From their web page: *"This first system was comprised of:"*
*......."9. New Delphi electronic control unit (ECU)—replaces NLA Digifant ECU and ICU (idle control unit)"* So, I would assume they kept that ECU in their latest design. There is speculation in a thread on the samba Vanagon forum regarding use of the new GW on a 1.9 WBX. Neil. On Thu, Jan 4, 2018 at 11:10 AM, Roy Nicholl <RNicholl@nbnet.nb.ca> wrote: > But not the idle stabilizer? > >> On 04-Jan-2018, at 13:45, Neil N <musomuso@GMAIL.COM> wrote: >> >> Below is a list copied from the GW web page showing parts used in >> their new system. >> >> New ECU >> New OBDII Scanner Compatible Data Connector New Knock Control Unit >> New Knock Sensor Vehicle Connections and Fuses Coolant Temp Connector >> [Uses Original Coolant Sender] Engine Position Unit [Replaces >> Distributor] Fuel Pump Wires [Uses Original Fuel Pump] System Relays >> Chassis Ground Fuel Injector Connectors [Uses Original Fuel >> Injectors] New Coils [Coil On Plug Design] Tachometer Adapter New >> Oxygen Sensor A/C Connector New Throttle Position Sensor Rebuilt >> Throttle Body New MAF Sensor and Housing [Replaces Airflow Meter] New >> MAP Sensor Power Steering Connectors Idle Air Control (IAC) Valve >> Connector [Uses Original IAC Valve] >>
-- Neil n Blog: Vanagons, Westfalia, general 1988 Westy Images 1981 Westfalia "Jaco" Images, technical Vanagon-Bus VAG Gas Engine Swap Group |
Please note - During the past 17 years of operation, several gigabytes of
Vanagon mail messages have been archived. Searching the entire collection
will take up to five minutes to complete. Please be patient!
Return to the archives @ gerry.vanagon.com
The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.
Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.