Date: Wed, 11 Apr 2018 13:57:49 -0700
Reply-To: Edward V Barger <edvbarger@MAC.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Edward V Barger <edvbarger@MAC.COM>
Subject: Re: flue vent assembly THANK YOU
In-Reply-To: <1B306A88-2C4D-48CA-BD19-B33DB1461584@shaw.ca>
Content-Type: text/plain; charset=utf-8
Thank you so much all is well now I needed to use a piece of masking tape to hold the outer ring in place while I screwed together
yes I did remove the tape
I lost one flue vent assembly one night It is parked in front of our house here in Venice Some one did the night time pick a part on it
nice surprise in the morning
This group is such a wonderful group of helpful on line friends
Now I need to find it's like for Lightroom and digital photo printing on the Epson 600 photo printer
I am just getting to that now that I have more time or will be as soon as I get caught up on all the neglected things Having two businesses
teaching and still trying to work as a Director of Photography just never had time to take care of the house garden and van
ed
Edward V Barger
edvbarger@mac.com
310 922 6251
> On Apr 10, 2018, at 7:10 PM, Alistair Bell <albell@shaw.ca> wrote:
>
> Don’t hesitate to email.
>
> The baffle plate, the flat plate with three semicircles and off set centre hole, can be awkward to position when putting on the exterior part. You can hold the baffle plate with your fingers thru the holes in the side of the exterior part when offering up to van.
>
> Make sure it’s seated right.
>
> And the two small machine screws in the end of the tube assembly, be careful not to cross thread or strip. The aluminum is soft.
>
> Ab
>
>> On Apr 10, 2018, at 6:45 PM, Edward V Barger <edvbarger@mac.com> wrote:
>>
>> Looks good will be at it tomorrow had to take pup to vet and phone kept ringing
>>
>> Thanks
>> Ed
>>
>> Sent from my iPhone
>>
>>> On Apr 10, 2018, at 5:45 PM, Alistair Bell <albell@shaw.ca> wrote:
>>>
>>> Jeeze ed, forgot about that blog post. Is it good enough?
>>>
>>> Ab
>>>
>>>> On Apr 10, 2018, at 8:30 AM, Edward V Barger <edvbarger@mac.com> wrote:
>>>>
>>>> Thanks I thought for sure would find a schematic some where and or one of the most knowledgeable folks on this site will know where it is
>>>>
>>>> You all have not failed me yet
>>>>
>>>> ed
>>>>
>>>>
>>>> Edward V Barger
>>>> edvbarger@mac.com
>>>> 310 922 6251
>>>>
>>>>
>>>>
>>>>> On Apr 9, 2018, at 6:54 PM, Alistair Bell <albell@shaw.ca> wrote:
>>>>>
>>>>> Hey,
>>>>>
>>>>> In case you didn’t get a good diagram, I’m willing to do some take apart pics for you
>>>>>
>>>>> Ab
>>>>>
>>>>>> On Apr 9, 2018, at 4:43 PM, Edward V Barger <edvbarger@MAC.COM> wrote:
>>>>>>
>>>>>> After more than 2 years finally getting the 87 ready for a camping trip in May
>>>>>>
>>>>>> Lots of details to take care of and then the packing up after checking every thing to make sure all is clean and working
>>>>>>
>>>>>> I can not remember exactly how all the parts of the flue vent assembly go back together and have not found a good diagram
>>>>>>
>>>>>> Have checked the Bentley and Go Westy but have not located a diagram
>>>>>>
>>>>>> Any one out there amounts the folks in the know …. know of such
>>>>>>
>>>>>>
>>>>>> thanks
>>>>>>
>>>>>> ed
>>>>>>
>>>>>>
>>>>>> Edward V Barger
>>>>>> edvbarger@mac.com
>>>>>> 310 922 6251
>>>>>
>>>>
>>>
>
|