Date: Fri, 22 Jun 2018 13:28:16 -0700
Reply-To: Stuart MacMillan <stuartmacm@GMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Stuart MacMillan <stuartmacm@GMAIL.COM>
Subject: Re: Engine Puzzlememt
In-Reply-To: <16428f97b20.27d5.f782c2410adfa1eb5e7c9b383baf9386@aol.com>
Content-Type: text/plain; charset=utf-8
Well, if it won’t turn 360 with the starter off it’s time to pull the tranny. It’s something in the bell housing jamming the TC or flex plate, or even something inside the engine. 😕
Stuart
> On Jun 22, 2018, at 12:29 PM, Tom Stone <tstone8359@aol.com> wrote:
>
> I took the starter out and spun the engine by hand as far as it would go. Other than some shiny teeth, probably from the starter misalignment, I didn't see any major damage. The ring gear is pretty hefty. How can I see the rest of the ring gear and what would damage that would stop engine rotation look like?
>
> Tom Stone, temporarily in Florida
>
>> On June 22, 2018 14:19:25 Tom Stone <tstone8359@aol.com> wrote:
>>
>> I took the plugs out and tried to turn the engine by hand in both directions. It stopped in the same places. I removed or disconnected all of the components connected to the engine yesterday. They all spun freely, but the engine would not. I will pull the starter off again and inspect the ring gear. Thanks for the suggestion.
>>
>> Tom Stone, temporarily in Florida
>>
>>> On June 22, 2018 14:00:55 "Stuart MacMillan" <stuartmacm@gmail.com> wrote:
>>>
>>> Are you using your hands on the pulley (or belt) to turn over the engine,
>>> which should be fairly easy with plugs out, or the starter? If you can turn
>>> the engine around fully by hand but not with the starter, you have a badly
>>> damaged ring gear on the torque converter. Probably happened when the
>>> starter mount was broken due to misalignment.
>>>
>>> Stuart
>>>
>>> -----Original Message-----
>>> From: Vanagon Mailing List <vanagon@gerry.vanagon.com> On Behalf Of Dennis
>>> Haynes
>>> Sent: Friday, June 22, 2018 10:35 AM
>>> To: vanagon@GERRY.VANAGON.COM
>>> Subject: Re: Engine Puzzlememt
>>>
>>> Short bolt bottom of starter?
>>>
>>> Sent from my Windows 10 phone
>>>
>>> From: Tom Stone<mailto:tstone8359@aol.com>
>>> Sent: Friday, June 22, 2018 12:22 PM
>>> To: Dennis Haynes<mailto:d23haynes57@hotmail.com>
>>> Cc: vanagon@gerry.vanagon.com<mailto:vanagon@gerry.vanagon.com>
>>> Subject: RE: Engine Puzzlememt
>>>
>>> Thanks Dennis and Jim. I pulled the spark plugs and there were no fluids
>>> inside the cylinders. Manually turned engine to stop point in both
>>> directions. It stops in the same places. I checked all three torque
>>> converter bolts. All seem tight. Going to remove some exhaust pieces to
>>> verify.
>>>
>>> Since the last change made to the engine was the installation of the starter
>>> long bolt, I am looking for some kind of obstruction in that area.
>>>
>>> Thanks for your always helpful suggestions.
>>>
>>> Tom Stone, temporarily in Florida.
>>>
>>>
>>>
>>> On June 21, 2018 19:08:09 Dennis Haynes <d23haynes57@hotmail.com> wrote:
>>>
>>> Look for a loose torque converter bolt. One of the three between converter
>>> and flex plate or something fell in there. Also, if multiple tries to crank
>>> engine the cylinders could be locked up with gasoline. Remove the spark
>>> plugs and check.
>>>
>>>
>>>
>>> Dennis
>>>
>>>
>>>
>>> Sent from my Windows 10 phone
>>>
>>>
>>>
>>> From: Tom Stone<mailto:tstone8359@AOL.COM>
>>> Sent: Thursday, June 21, 2018 6:01 PM
>>> To: vanagon@GERRY.VANAGON.COM<mailto:vanagon@GERRY.VANAGON.COM>
>>> Subject: Engine Puzzlememt
>>>
>>>
>>>
>>> Working on my son's '91 Westy Automatic. New engine from the guy that took
>>> over Boston Bob's business. It was installed and running. The starter had
>>> been installed with only the short bolt which had loosened. The starter lost
>>> ground and would only work intermittently. Then the bolt ear broke. I got a
>>> new starter and the long bolt and installed it with both bolts. Now the
>>> engine will only rotate to a certain point and stop. I can manually turn the
>>> engine backwards and it stops turning at just before the stop point. I took
>>> the starter off and ran it. I took the belts off the P/S pump, the
>>> alternator and the water pump (A/C not connected) and they all turn freely.
>>> I took the valve covers off and without being able to rotate the engine,
>>> visually checked for a valve stem in each keeper. I am at a loss for what to
>>> look at next and what might have happened.
>>>
>>>
>>>
>>> Any ideas?
>>>
>>>
>>>
>>> Tom Stone, temporarily in FL where it is hot!
>
>
>
|