Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (October 2020, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 23 Oct 2020 15:53:47 -0400
Reply-To:     Geoffrey Toye <geoffreytoye@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Geoffrey Toye <geoffreytoye@GMAIL.COM>
Subject:      Re: 1981 2L Type IV Strainer Cleaning - Where Does the Rubber
              Washer Go?
Comments: To: Neil N <musomuso@gmail.com>
In-Reply-To:  <CAB2RwfioaLKQC=bf0eG=2Fz1jg0nhmAw0uQ7YwUFSAdTOc_S6w@mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"

Thanks Neil, I’m beginning to think it is real debris also. Will look at the pushrod tube seals for leaks.

Cheers

Geoff T

The drain plug is oversized and sealed with a nylon washer. I torque to 12 ft lb and it seals good.

On Fri, Oct 23, 2020 at 3:25 PM Neil N <musomuso@gmail.com> wrote:

> You may've seen this but here's an ETKA or similar drawing for a US > market 1981 2.0: > > image link: > https://volkswagen.7zap.com/ImgsWatermark/images//Bilder/004/004010000.png > > page with part numbers etc: > > https://volkswagen.7zap.com/en/usa/vanagon/va/1981-4/1/115-10000/ > > Long shot theory: a poorly installed O ring at a push rod tube came > loose and fell into sump? > > Or, O ring was installed at drain plug to help quell a leak? I'd > inspect the drain hole threads at case regardless. > > Neil. > > On 10/23/20, Geoffrey Toye <geoffreytoye@gmail.com> wrote: > > > I am cleaning the oil strainer on a 2L Type IV motor in my 1981 Westie > for > > the first time (under my ownership). I bought a gasket set that includes > > the two large paper gaskets and the aluminum crush washer. However, > when I > > took the strainer off, in addition to the three gaskets I have in the > kit a > > fourth rubber washer came out? I am not sure where it came from but it > > came out with the strainer itself. Also, it's split and I assume it > should > > be replaced. Looking at the parts catalog I have I see no mention of it. > > Any > > ideas guys and girls where this goes? > > > > > -- > Neil n > > VE7TBN > > 1988 Westy 50º ABA swap: https://tinyurl.com/yap5hpwt > > 1981 Westy 15º ABA swap: https://tinyurl.com/y9n4xob8 > > VAG Gas Engine Swap Group <http://tinyurl.com/khalbay> >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.