Date: Mon, 24 May 2021 22:03:04 -0400
Reply-To: Larry Alofs <lalofs@GMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Larry Alofs <lalofs@GMAIL.COM>
Subject: Re: Discovered my clutch failure reason.
In-Reply-To: <E87486E2-0F32-488C-9BDD-3FB5394FCC7B@shaw.ca>
Content-Type: text/plain; charset="UTF-8"
Lots of shear stress on that roll pin. Carry some extras.
Larry A.
On Mon, May 24, 2021 at 7:12 PM Alistair Bell <albell@shaw.ca> wrote:
> Was thinking same but straight pin.
>
> Roll pin better.
>
> Alistair
>
> > On May 24, 2021, at 4:10 PM, Dennis Haynes <d23haynes57@hotmail.com>
> wrote:
> >
> > Fabricate an arm with ball stud and 20mm hole. Drill shaft end with arm
> in position for 5 mm roll pin.
> >
> > Dennis
> >
> >
> > -----Original Message-----
> > From: Vanagon Mailing List <vanagon@gerry.vanagon.com> On Behalf Of
> Alistair Bell
> > Sent: Monday, May 24, 2021 6:37 PM
> > To: vanagon@GERRY.VANAGON.COM
> > Subject: Re: Discovered my clutch failure reason.
> >
> > Oh Neil, you’re as bad as me :-)
> >
> > Nope, bug arm has splines in diff place.
> >
> > I’ll find a used one I’m sure. But it has given me a few hours of
> thought about how I would go about making a sub. I’d do away with the
> splines in the arm as I can’t make them… I’d do some other way.
> >
> > Oh btw, the clutch cross shaft is a nice 19.99 mm diameter where the arm
> goes on. It’s a nice close fit to the arm ( haven’t measured arm bore yet.
> I’ll guess it’s 20.00mm)
> >
> > Alistair
> >
> >> On May 24, 2021, at 3:10 PM, Neil <musomuso@gmail.com> wrote:
> >>
> >> If by some miracle a Bug COL fit, I think it would be pretty easy to
> >> weld a ball to arm:
> >>
> >> https://na01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.t
> >> hesamba.com%2Fvw%2Fclassifieds%2Fdetail.php%3Fid%3D2318059&data=04
> >> %7C01%7C%7C77ba6bd43b4043d0546f08d91f046790%7C84df9e7fe9f640afb435aaaa
> >> aaaaaaaa%7C1%7C0%7C637574926044051858%7CUnknown%7CTWFpbGZsb3d8eyJWIjoi
> >> MC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&
> >> sdata=rENNpAiLFOrkY0V%2Fw5i5xSsevE1UCc3nsiH6ZquJ8W4%3D&reserved=0
> >>
> >> Neil.
> >>
> >>>> On 5/24/21, Neil <musomuso@gmail.com> wrote:
> >>>
> >>>
> >>> Sorry. Looked in all my boxes of Vanagon parts. No COL.
> >>
> >>
> >> --
> >> Neil n
> >>
> >> VE7TBN
> >>
> >> 1988 Westy 50º ABA swap:
> >> https://na01.safelinks.protection.outlook.com/?url=https%3A%2F%2Ftinyu
> >> rl.com%2Fyap5hpwt&data=04%7C01%7C%7C77ba6bd43b4043d0546f08d91f0467
> >> 90%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637574926044061859%7CU
> >> nknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1ha
> >> WwiLCJXVCI6Mn0%3D%7C1000&sdata=5kc2kQFq%2Bwubn5zgvXxM4Jz1a6wcjevqh
> >> MDFmKc64ZE%3D&reserved=0
> >>
> >> 1981 Westy 15º ABA swap:
> >> https://na01.safelinks.protection.outlook.com/?url=https%3A%2F%2Ftinyu
> >> rl.com%2Fy9n4xob8&data=04%7C01%7C%7C77ba6bd43b4043d0546f08d91f0467
> >> 90%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637574926044061859%7CU
> >> nknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1ha
> >> WwiLCJXVCI6Mn0%3D%7C1000&sdata=6NuXa7UM3AuEsiTeEOsnw6WXwr%2BLWTb%2
> >> F93E9wpSPWzI%3D&reserved=0
> >>
> >> VAG Gas Engine Swap Group
> >> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Ftinyu
> >> rl.com%2Fkhalbay&data=04%7C01%7C%7C77ba6bd43b4043d0546f08d91f04679
> >> 0%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637574926044061859%7CUn
> >> known%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haW
> >> wiLCJXVCI6Mn0%3D%7C1000&sdata=wq1jzL68qstD3%2B94P0B0iALIyGmpmIZxfx
> >> 1L%2BLaeRfc%3D&reserved=0>
>
|