Date: Fri, 2 Jul 2021 18:09:02 -0400
Reply-To: Steven Shelton <shelton4@GMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Steven Shelton <shelton4@GMAIL.COM>
Subject: Re: Engin hatch insolation project
In-Reply-To: <B477DADA-2DF9-46EE-8CC4-867216D8D66E@comcast.net>
Content-Type: text/plain; charset="UTF-8"
It took a good while to get the old stuff off and most of it was already
cut out to raise the lid! I collected all the scraping tools I could find
and just went to work. I can't remember what solvent I ended up using.
I just stuck the Hoodliner to the inside of the lid. No wire. It's so much
lighter than the original foam I don't think it's going anywhere. I cut it
as close as I could; I even made cardboard patterns to fit curves and
corners. I put B-Quiet Ultimate Sound Deadener in the raised portion
because there is little clearance between the engine and the cover.
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=icon>
Virus-free.
www.avast.com
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=link>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
On Fri, Jul 2, 2021 at 11:25 AM Eric Caron <ericcaron96@comcast.net> wrote:
> Yes,
> That is the same product I’m have here.
>
> So, can you add some details to the info on the work you did to prep and
> how you attached it?
>
> Example.
>
> So far, I have
>
> Started to scrape out the foam with a thin putty knife.
> There were wires in the foam, part of the structure. I was able to simply
> pull them out completely.
> I found it isn’t just a oval there are ridges going left to right
> perpendicular to the wave of the hatch.
>
> There is also foam along the edge.
>
> How did you remove foam?
> At the end did you sand or use Gu gone or something?
> Did you adhere to the plastic directly and how is that holding up?
>
> Did you cut the liner to fit inside the the raised ridges?
>
> Did you add something to make sure it stayed up such as a few wires?
>
> I would love to learn from your project.
>
> I’m at the removal sage and as I’m about to host a camp out for West River
> Westies the project will be on hold after cleaning.
> Details and even a pic of your final results appreciated!
>
> Eric Caron
>
>
> > On Jul 2, 2021, at 10:29 AM, Steven Shelton <shelton4@GMAIL.COM> wrote:
> >
> > I did mine a few months ago. I used Dynamat Hoodliner (Dynamat Hoodliner
> > Stop Road Noise! at Crutchfield
> > <https://www.crutchfield.com/p_15411905/Dynamat-Hoodliner.html>). It
> was a
> > mess to get the old stuff out but in the end it turned out pretty well.
> > Here's a photo: https://www.thesamba.com/vw/gallery/pix/2135709.jpg. My
> > engine cover had to be raised slightly to make room for a conversion
> > engine, so your results may vary.
> >
> > <
> https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=icon
> >
> > Virus-free.
> > www.avast.com
> > <
> https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=link
> >
> > <#m_-3933517257253470064_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
> >
> > On Thu, Jul 1, 2021 at 10:22 PM Thomas Casal <thomas.casal@gmail.com>
> wrote:
> >
> >> Cascade audio has a pretty nice heat sound barrier super thick foam
> that I
> >> keep thinking I wanna use to replace the foam on the engine cover and
> above
> >> the trans but I’m afraid to open that can of worms. Good luck.
> >>
> >> On Thu, Jul 1, 2021 at 8:58 PM Eric Caron <ericcaron96@comcast.net>
> wrote:
> >>
> >>> Hi folks,
> >>>
> >>> Anyone ever remove the foam and replace with a modern sound and heat
> >>> product?
> >>>
> >>> I’m starting the project now and it may take longer than Alistair
> >>> refreshing his engine and transmission.
> >>>
> >>> That stuff is ugly!
> >>>
> >>> Fingers crossed the final solution comes out functional and reasonably
> >>> nice looking.
> >>>
> >>> Eric Caron
> >>> I’m becoming one with my putty knife.
> >>>
> >>
> >
> > <
> https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=icon
> >
> > Virus-free.
> > www.avast.com
> > <
> https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=link
> >
> > <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
>
>
|