Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (June 2022, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 22 Jun 2022 09:47:36 -0700
Reply-To:     Gene P <olgreywoof@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Gene P <olgreywoof@GMAIL.COM>
Subject:      Re: Manual transmission lesson request
Comments: To: Eric Caron <ericcaron96@COMCAST.NET>
In-Reply-To:  <CD0A35D7-64D0-4286-AC5F-8A7639A49A66@comcast.net>
Content-Type: text/plain; charset="utf-8"

I have not gone out to refresh memory, but on the passenger side and hiding behind the shift lever. So find where the horizontal shift rod connects to the vertical flat lever with the ball. Behind that lever. Or … find the place on the passenger side of the transaxle where it would be most difficult to get a fat hex wrench – that’s where the plug is.

gp

‘87 T3 ‘81 R65 ‘61 TR3

From: Eric Caron Sent: Wednesday, June 22, 2022 6:39 AM To: vanagon@GERRY.VANAGON.COM Subject: Re: Manual transmission lesson request

Thanks Bob,

so much easier then the Auto transmission.

I found the drain plug no problem.

Where is the fill plug? I’ll probably find it with the next trip under the van but knowing what side and about how high up is helpful. I was looking for something that felt like the drain plug.

Any favorite manual oils out there? Can I use the same as that in the auto final drive?

My neighbors are getting used to seeing my feet sticking out from the van as they walk by. They now expect a waive from feet.

Eric Caron

> On Jun 22, 2022, at 6:55 AM, Mbob1950 <mbob1950@GMAIL.COM> wrote: > > Make sure your hex tool fits tightly into the drain plug. Plug may need cleaning. > Some hex tools have rounded edges on the tip. I have found that grinding the tip rounded edges flat will give a better bite on the plug for removal. > Remove the fill plug. Remove the drain and catch old oil. > Clean drain plug and magnet and reinsert. > Fill with new gear lube. And insert fill plug. > > > Bob > > 1986 Syncro ‘Bullet’ > 1991 WESTY ‘Sylvan’ > > >> On Jun 21, 2022, at 23:36, Eric Caron <ericcaron96@comcast.net> wrote: >> >> Good point! And, not something I would have thought about, but I will now remember. >> >> And, should I ask you how you know this? >> >> Now what is the rest of the process? >> >> Eric Caron >> >> >>> On Jun 21, 2022, at 10:39 PM, Dan N <dn92610@GMAIL.COM> wrote: >>> >>> Rule #1 when changing the oil of a manual transmission is removing the top >>> filler plug first. >>> If you can't do that then you still oil in there to drive a shop. If you >>> drain the oil and can't refill then you will need a tow.


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.