Date: Tue, 05 Apr 94 22:33:51 CDT
Sender: Vanagon Mailing List <vanagon@vanagon.com>
From: Joel Walker <JWALKER@ua1vm.ua.edu>
Subject: technical bulletins for vanagons, campers, syncros
me again. and, no, i don't ... i'm a government worker! :)
anyhoo, here are some vw tech bulletins (which you, too, can get for yourself
from Dyment Publications!!) about vanagons. see if you want this stuff. if
so, i'll try to type in the rest about vanagons. only trouble is, i can't
draw the pictures (like the one about replacing cylinder head gaskets).
(the tech bulletin about derek's stuttering/dying harness fix is in here)
...........................................................................
from Service Bulletins, Model Year 1985
.........................................................................
VW Technical Information
Group 19, Number 87-03
Date: December 21, 1987
Model(s): Vanagon, Water-cooled, model years 1983-1985
Subject: Carpet wet by rear seat - heat exchanger T-piece leaking
A coolant leak in the rear heat exchanger area may be due to poor hose fit
at the metal T-piece which connects the fee hose to the main coolant hose.
An imporved, white plastic T-piece with slightly larger diameter is available
to correct this condition:
* Replace metal T-piece with white plastic version, Part number 253-265-543A
* Remove flow restrictor from inlet fitting of heater valve.
Production Change:
Improved T-piece installed as of Nov. 1984, VIN 25 FH 037 898.
............................................................................
from Service Bulletins, Model Year 1985
.........................................................................
VW Technical Information
Group 80, Number 87-01
Date: July 31, 1987
Model(s): Water-cooled Vanagons, 1983-1985
Subject: Carpet wet by rear seat - heat exchanger bleeder screw broken
The plastic bleeder screw for the rear heat exchanger may be broken due to
seal swelling.
* Replace with an improved metal bleeder screw, Part number N 902 061 01.
and new gasket, Part number 861 819 037.
Production Change:
Metal bleeder screw installed as of:
December 1984, VIN: 25 FM 050 887
...........................................................................
Technical Information
Group 87, Number 89-01, August 31, 1989
Model(s): Vanagon with A/C, model years 1986-1989
Subject: Evaporator Housing - change
Starting April 1988, a running change was made to the evaporator housing and
introduced into production.
To prevent cracking, the body attachment points have been relocated.
Evaporator housings are now available through the parts depot and come as a
multiple supersession with the following items:
1 evaporator housing (color coded)
2 mounting brackets
2 shims (color coded)
6 rivets
6 body plugs (color coded)
6 bolts
INSTALLING
- disconnect battery
- remove front A/C control assembly and center vents
- remove both rear side covers at C-pillars
- remove both outside vent covers
- remove relay assembly from left C-pillar adn all tie wraps holding A/C lines
- remove evaporator housing fasteners and lower housing
NOTE
Discharging the A/C system is NOT required due to the length of the evaporator
hoses. A cherry picker with a protective cover helps in lowering the
evaporator housing.
- bolt brackets to new evaporator housing and lift into postion
- with the evaporator firmly positioned against the roof, work through the
speaker holes, mark location of new bracket attachment points approximately
40 mm (1.575 in.) above the original holes
- lower evaporator housing, center punch and drill holes to accomodate rivets
NOTE
Rivets can be installed using Kent-Moore tool #M-39010
- install original covers on bolt heads
- install remaining components
Labor Operation Number: 8760-31-0
Suggested Repair Time: 280 t.u.
............................................................................
Technical Bulletin
Group: 90
Number: 90-02