Date: Thu, 11 Dec 1997 15:52:42 -0800
Reply-To: "L-Soft list server at Vanagon List (1.8c)"
<LISTSERV@GERRY.SDSC.EDU>
Sender: Vanagon Mailing List <Vanagon@Gerry.SDSC.EDU>
From: "L-Soft list server at Vanagon List (1.8c)"
<LISTSERV@GERRY.SDSC.EDU>
Subject: Re: engine swap (ignorant questions) -> EV piston slap
>> STOP THIS !!!!!!!!!!!!!!!!!
> You are not authorized to use the STOP command.
Unknown command - "YOU". Try HELP.
>> L-Soft list server at Vanagon List (1.8c) wrote:
> Unknown command - "L-SOFT". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> All Audi I-5 engines I've seen fitted to Audi 4K, 5K, 80, 90, 100, 200,
>>>
>>> > Unknown command - "ALL". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> and VW Quantum are canted at approx 15-20 degrees.
>>>
>>> > Unknown command - "AND". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> rb
>>>
>>> > Unknown command - "RB". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> ----------------------------
>>>
>>> > Unknown command - "----------------------------". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> Scot wrote:
>>>
>>> > Unknown command - "SCOT". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> I don't believe "Piston Slap" is HYPE, as it was claimed. I have a
>>>
>>> > Unknown command - "I". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> question about the angle of the inline 5 as it is used in the Audi; do
>>>
>>> > Unknown command - "QUESTION". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> the pistons travel vertically, or is there some angle set from
>>>
>>> > Unknown command - "THE". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> vertical? I know from my EV that the engine is on an angle and if the
>>>
>>> > Unknown command - "VERTICAL?". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> >> engine was designed to run upright, there is a very good chance of
>>>
>>> > Unknown command - "ENGINE". Try HELP.
>>> Unknown command - "UNKNOWN". Try HELP.
>>>
>>> All subsequent commands have been flushed.
>>>
>>> Your message did not contain any command. Note that lines starting with a
>>> "greater than" sign ('>') are ignored.
>>>
>>> Summary of resource utilization
>>> -------------------------------
>>> CPU time: 0.015 sec
>>> Overhead CPU: 0.000 sec
>>> CPU model: 2x90MHz Pentium (64M)
>> --
>> http://www.zstarr.com/impex
> Your message did not contain any command. Note that lines starting with a
Unknown command - "YOUR". Try HELP.
> "greater than" sign ('>') are ignored.
Unknown command - ""GREATER". Try HELP.
> Summary of resource utilization
Unknown command - "SUMMARY". Try HELP.
> -------------------------------
Unknown command - "-------------------------------". Try HELP.
> CPU time: 0.016 sec
Unknown command - "CPU". Try HELP.
> Overhead CPU: 0.000 sec
Unknown command - "OVERHEAD". Try HELP.
> CPU model: 2x90MHz Pentium (64M)
Unknown command - "CPU". Try HELP.
Your message did not contain any command. Note that lines starting with a
"greater than" sign ('>') are ignored.
Summary of resource utilization
-------------------------------
CPU time: 0.015 sec
Overhead CPU: 0.000 sec
CPU model: 2x90MHz Pentium (64M)