Date: Thu, 11 Dec 1997 15:52:45 -0800
Reply-To: "L-Soft list server at Vanagon List (1.8c)"
<LISTSERV@GERRY.SDSC.EDU>
Sender: Vanagon Mailing List <Vanagon@Gerry.SDSC.EDU>
From: "L-Soft list server at Vanagon List (1.8c)"
<LISTSERV@GERRY.SDSC.EDU>
Subject: Re: engine swap (ignorant questions) -> EV piston slap
>>> STOP THIS !!!!!!!!!!!!!!!!!
>> You are not authorized to use the STOP command.
> Unknown command - "YOU". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>>> L-Soft list server at Vanagon List (1.8c) wrote:
>> Unknown command - "L-SOFT". Try HELP.
> Unknown command - "UNKNOWN". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> All Audi I-5 engines I've seen fitted to Audi 4K, 5K, 80, 90, 100, 200,
>>>>
>>>> > Unknown command - "ALL". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> and VW Quantum are canted at approx 15-20 degrees.
>>>>
>>>> > Unknown command - "AND". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> rb
>>>>
>>>> > Unknown command - "RB". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> ----------------------------
>>>>
>>>> > Unknown command - "----------------------------". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> Scot wrote:
>>>>
>>>> > Unknown command - "SCOT". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> I don't believe "Piston Slap" is HYPE, as it was claimed. I have a
>>>>
>>>> > Unknown command - "I". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> question about the angle of the inline 5 as it is used in the Audi; do
>>>>
>>>> > Unknown command - "QUESTION". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> the pistons travel vertically, or is there some angle set from
>>>>
>>>> > Unknown command - "THE". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> vertical? I know from my EV that the engine is on an angle and if the
>>>>
>>>> > Unknown command - "VERTICAL?". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> >> engine was designed to run upright, there is a very good chance of
>>>>
>>>> > Unknown command - "ENGINE". Try HELP.
>>>> Unknown command - "UNKNOWN". Try HELP.
>>>>
>>>> All subsequent commands have been flushed.
>>>>
>>>> Your message did not contain any command. Note that lines starting with a
>>>> "greater than" sign ('>') are ignored.
>>>>
>>>> Summary of resource utilization
>>>> -------------------------------
>>>> CPU time: 0.015 sec
>>>> Overhead CPU: 0.000 sec
>>>> CPU model: 2x90MHz Pentium (64M)
>>> --
>>> http://www.zstarr.com/impex
>> Your message did not contain any command. Note that lines starting with a
> Unknown command - "YOUR". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>> "greater than" sign ('>') are ignored.
> Unknown command - ""GREATER". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>> Summary of resource utilization
> Unknown command - "SUMMARY". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>> -------------------------------
> Unknown command - "-------------------------------". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>> CPU time: 0.016 sec
> Unknown command - "CPU". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>> Overhead CPU: 0.000 sec
> Unknown command - "OVERHEAD". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
>> CPU model: 2x90MHz Pentium (64M)
> Unknown command - "CPU". Try HELP.
Unknown command - "UNKNOWN". Try HELP.
> Your message did not contain any command. Note that lines starting with a
Unknown command - "YOUR". Try HELP.
All subsequent commands have been flushed.
Your message did not contain any command. Note that lines starting with a
"greater than" sign ('>') are ignored.
Summary of resource utilization
-------------------------------
CPU time: 0.032 sec
Overhead CPU: 0.000 sec
CPU model: 2x90MHz Pentium (64M)