Date: Sun, 2 Aug 1998 00:57:29 -0800
Reply-To: Otmar Ebenhoech <Otmar@EVCL.COM>
Sender: Vanagon Mailing List <Vanagon@vanagon.com>
From: Otmar Ebenhoech <Otmar@EVCL.COM>
Subject: Re: '73 tranny trashed?-Reply
In-Reply-To: <36be43c6.35c3da34@aol.com>
Content-Type: text/plain; charset="us-ascii"
><< At 2:08 PM -0500 8/1/98, Harmon Seaver wrote:
>
> >I just pulled the engine on my '73 westy -- somehow the
> >tranny main shaft pulled out with it. Not all the way, of
> >course, but it now comes out about 6-8 inches from
> >where it should be, and no longer connects to anything
> >inside........
>
>To which Otmar Ebenhoech replied:
>
><< No Problem. Just push it back in, rotate it a bit to make
>the splines line up.
>
> This is a common problem, the threads that hold the input
>shaft in are stripped. I've run a few trannys like that for years>>
>
>------------------------------------------------------------------------------
>--------------
>
>Ok, now for my 2 cents or so:
>
>How do you get the coupler for the mainshaft and input shaft
>on then?? I don't see any way to do this job without removing
>the bellhousing. The reason that the input shaft comes out 6
>or so inches is that the snap ring retainer for the coupler is still
>on the input shaft and is striking the backside of the bellhousing
>bore hole. This means that the coupler and its internal splines
>to match the external spline on the above mentioned shafts is
>either still on the mainshaft or has fallen off and is laying some-
>where in the differential section. The bellhousing has to come
>off. How else can you screw the shafts together and then slide
>the coupler down the input shaft onto the matching splines on
>the mainshaft and have the coupler's external teeth for the
>reverse sliding gear shaft mate with it's gear? Oh, and then slide
>the snap ring down the input shaft and seat it in it's groove? If this
>isn't making sense then take a peek at your Bentley and you'll see
>those splines, coupler, and snap ring. I can see how you could
>fish around and get the two shafts to line up and thread together
>but the coupler part has me stumped.
>
>Todd Hill
>VolksWerks Transaxles
>Olympia, WA
Still no problem.
The coupler (with reverse gear) is too big to slide off the shaft (except
when the diff is in just the right place with some wiggling) It's on the
mainshaft, belive me, unless you have super psychokinetic powers.
So, the gear stays in place and the snap ring stays on the input shaft.
The threads are stripped (how do you think it came off?) so you won't need
to thread it back on. Just push it in and off you go. It's really quite
simple. If you have some strange crankshaft with too deep of a hole, or if
your input shaft has been cut off then you better fix it right. But if it's
stock then don't worry about it. How many years has it been running this
way anyway?
I had a VW tranny with a 2.9L ford V6 plugged into it that would pull out
the input shaft when I pulled the engine (plus a few during the 10 years of
VW wrenching that I used to do) and I never had a problem with them after
just pushing them back in.
Have fun!
-Otmar-
-----------------------------------------------------------------------
Otmar Ebenhoech Electric Vehicle Components Ltd.
"I wish I die sleeping peacefully like my grandfather,
not screaming in terror like his passengers"
Otmar@EVCL.com http://www.evcl.com (650) 494-9255
-----------------------------------------------------------------------
|