Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (March 1999, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 20 Mar 1999 10:39:27 -0700
Reply-To:     Karl Wolz <wolzphoto@ATT.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Karl Wolz <wolzphoto@ATT.NET>
Subject:      Re: CV joint repair?
Comments: To: kenneth d lewis <kdlewis@JUNO.COM>
Content-Type: text/plain; charset="iso-8859-1"

You can get a twelve point wrench at BAP. Bring your bolt, as the sizing is confusing, like they call a 6mm an 8 or vice versa.

The unit they sell is a peice of hex bar stock which is cut into a twelve point on one end, so you put it into a socket to use it. They are a bit hard to use, since they tend to fall out of the socket (though they do work).

If you want a real wrench, you need to go to Snap-On or MAC tools or one of the other pro tool dealers.

At least in theory, the twelve points work better, giving the wrench a better grip.

Karl Wolz

-----Original Message----- From: kenneth d lewis <kdlewis@JUNO.COM> To: vanagon@GERRY.VANAGON.COM <vanagon@GERRY.VANAGON.COM> Date: Saturday, March 20, 1999 10:18 AM Subject: Re: CV joint repair?

>Stuart; > Hmmmm.. I remember assembling an axle and splined stub on the >work bench and trying to install it as a unit on my 86. Due to the >suspension box and angle it would not GO IN! I had to separate them and >put the stub in by itself.What year vehicles did you have success with >this procedure? > I am glad you brought up the TORX thing. The new CV boot kit came >with "cap bolts" that had twelve point bolts. Sears did not have anything >that looked like that. Where do you get them. The 6mm allen did fit fine. > >Drive Safely & Good Luck >Ken Lewis<Kernersville,NC>86 VW crewcab;60 T-5 Coupe > >On Fri, 19 Mar 1999 14:43:31 -0800 Stuart MacMillan ><stuart@COBALTGROUP.COM> writes: >>Kenneth, >> >>Next time remove the transmission side cap screws, then remove the >>brake >>drum and flange (not always easy either) and tap out the splined stub >>axle with a soft mallet >> >>Also, I have run into Torx type cap screws on CV joints, and an allen >>wrench will almost always strip these out. Just adds to the fun! Now >>I >>replace all the cap screws when I do the first CV replacement. >> > >___________________________________________________________________ >You don't need to buy Internet access to use free Internet e-mail. >Get completely free e-mail from Juno at http://www.juno.com/getjuno.html >or call Juno at (800) 654-JUNO [654-5866] >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.