Date: Wed, 5 May 1999 04:44:10 -0700
Reply-To: Max/Joyce Wellhouse <maxjoyce@IPA.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Max/Joyce Wellhouse <maxjoyce@IPA.NET>
Subject: Re: Oil Cooler Upgrade I did...
Content-Type: text/plain; charset="iso-8859-1"
260270 degrees is real hot by VW standards(assuming your guage is accurate).
In the old hot rodding VW engines book from the 60's, they said for every 10
degrees your engine runs above 200 degrees, it cuts your engine life in
half!!! Check guagew accuracy by removing temp sensor(VDO aftermarket I
assume) and set up your camp stove and boil water. Assuming your near sea
level, the water will boil at 212 degrees F
stick the sensor in the boinling water and turn on the ignition so juice
gets to the sender and rig up a ground clip for the completed circuit.
Won't take long for the reading to show how far you're ofI rigged up an old
Harrison evaporator condenser from a 75 Monte Carlo's AC and welded 2 1/2
inch aluminum pipe thread fittings on the inlet and outlets, and rigged up
an Amot in -line thermosatat. Add the Aeroquip teflon/ SS braided hose and
the swedgemated fittings and voila!: You
hAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAZZZZZZZZZZZZZ
ave 200 degree oil on a very hot day. Airflow was through a semi
sophisticated sheet metal conduit stealing the air from the side louver.
This was a 79 busss
-----Original Message-----
From: Bill Knight <bill@NS.ESC.STATE.NC.US>
To: vanagon@GERRY.VANAGON.COM <vanagon@GERRY.VANAGON.COM>
Date: Tuesday, May 04, 1999 1:33 PM
Subject: Re: Oil Cooler Upgrade I did...
>Regarding the oil cooler, how did you connect it to the engine? I am
>contemplating an external cooler for my 2.1 upgrade in my 84 Westfalia. I
>find that the bigger motor runs at 260 degrees or more. Due to using the
>original cooling system, I could not use the factory oil cooler and am
>looking into alternatives.
>
>Also, what is the general consensus about maximum oil temperature range?
Is
>260-270 degrees way too high? My old engine never got above 240. I am
>measuring the temperature in the oil galley near the oil filter using a VDO
>sensor in the second oil pressure switch location. On my old engine I
>measured the temp in the sump. Is the oil hotter after being compressed by
>the oil pump?
>
>Bill
>
>-----Original Message-----
>From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com]On Behalf
>Of Joseph Tu
>Sent: Tuesday, May 04, 1999 1:05 PM
>To: vanagon@GERRY.VANAGON.COM
>Subject: Oil Cooler Upgrade I did...
>
>
>Hello,
>
>I am just putting in what I did for an add on oil cooler for my van. The
>factory oil cooler is great, but I feel that it has too little surface
>area and the is too small for sufficient heat transfer when the fluids
>pass by. So I opted to add another one. It was an air to oil cooler and
>it is made by Setrab. I purchased it through the autotech guys, since
>they are located pretty near where I live. Anyways, as for location, I
>chose to put the cooler in the area just fore of the transmission, the
>angled surface that is the back of the storage space under the rear
>bench. Although This isn't the best location for air flow, it presented
>the least difficulty in mounting, which was my main goal. I thought about
>mounting it up front, near the radiator, but then I thought abou the
>length of hose the oil would have to travass and possible pressure loss,
>which would mean a higher flow/pressure oil pump, nada for me! I want to
>also have some metal ducting added on to route air traveling under the
>van through the fins of the cooler. I would recommend using a quality
>cooler like Setrab or maybe Earl's(not sure if this is a nationally known
>brand). Its not a cheasy aluminum fin cooler, with the pipe running
>through it. It's similar in design to the factory oil coolers on the air
>cooled bus/bug etc. Anyways, thats my 2 cents.
>
>Joe Tu
|