Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (May 1999, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 14 May 1999 11:21:02 -0400
Reply-To:     The Bus Depot <ron@NETCARRIER.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         The Bus Depot <ron@NETCARRIER.COM>
Subject:      Re: Bus Depot Trailer Hitch
Comments: To: David Beierl <synergx@ibm.net>
In-Reply-To:  <4.2.0.37.19990513233732.06bb9560@pop01.ny.us.ibm.net>
Content-Type: text/plain; charset="iso-8859-1"

> Well, the trailer hitch from Bus Depot arrived today. It is > amazing. Ron didn't do it justice in his description. It > weighs about 35 pounds (16 kg)! If it weren't hidden inside > the bumper it would have to be registered as an offensive weapon. > > Unfortunately it didn't come with an installation sheet -- Ron, > was that an oversight?

No, the manufacturer didn't provide one. When they first came, I took the bumper off of my '89 and tried it out myself. Installing the main unit itself is obvious; you just remove the bumper brackets and slide it into the holes the brackets slid into, then put the screws back in.

What's less obvious is the way the mounts for your bumper attach to the hitch. There are two pairs of mounts included; one set is L-shaped and one is more oddly shaped.

If you have the plastic bumpers you will find that the oddly-shaped ones match perfectly with the holes in your bumper that the original bumper brackets used. Once you attach these brackets, you can push the bumper generally into place, and then you will see where you will have to notch the bottom of the bumper in order to allow it to clear the hitch plate and push all the way forward to the correct position.

If you have a metal bumper, it uses the L-shaped mounts. As I recall, the long arm of the L attaches to the hitch and the short arm to the bumper's existing bolt holes. Again, when you then attempt to push the bumper into place you will see where you will have to notch the bottom of the bumper in order to let it push fully forward to clear the hitch plate. As I noted in my original post, it looked to me when trying this on my van that unless you drilled an additional hole in the L-shaped mounts (to attach the bumper more flush with the hitch), the bumper would sit too far back. But Just Kampers tells me that I am mistaken. I suppose this is possible, since after attaching the brackets, I didn't finish the job by actually notching the bumper and bolting it on; I was playing with a brand new bumper that was about to be shipped to a customer, and didn't want to send it "pre-notched" for a hitch he didn't have!

> First is that I don't see immediately any place for attaching safety chains.

I suppose that the safety chains in Europe are a bit different from here, but there are a couple of spots on the hitch that you could use to attach a safety chain: the two holes below the ball hitch that you are not using, or there are two holes below it near where the flat plate is welded to the hitch. I'm not sure whether or not these holes are large enough for the diameter of the standard S-hook on a trailer, but it wouldnt be hard to either add a second S-hook or replace the ones on the trailer. Doesn't look like it would be a big deal.

> Second is a metal plate, about 75mm by 160mm by 3mm. > One end is semicircular, the other is a rounded-off triangle.

Just Kampers tells me that this is a standardized mount for a trailer electrical hookup - European standard, that is. Completely useless here, I suppose, just throw it away.

- Ron Salmon The Bus Depot, Inc. http://www.busdepot.com (215) 234-VWVW


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.