Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (May 1999, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 24 May 1999 11:28:02 -0400
Reply-To:     "Stanley, Kerry" <kstanley@CAS.ORG>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         "Stanley, Kerry" <kstanley@CAS.ORG>
Subject:      Re: SOS: Waterpump Questions: Help!
Content-Type: text/plain; charset="iso-8859-1"

Hi all,

I had my water pump go last fall. I had no warning, except for age that is was about to go. I did drive home from Boston to Philly. It was noisy and starting to leak. On removal there was a little scoring as Dennis describes, but not too bad, so I just replaced the pump. I've had no cooling problems with the replacement pump, although I have not driven in 90-100 degree weather since then.

Now replacement that is another story. It is a real bugger to get out. The hex socket bolts holding on the pipe going to the right side head are very difficult to get too. One can be reached with an extender from under the bumper, but the other one is real tuff to get to. I did use a 3/4 - 1" section of appropriate hex allen wrench with the same size box wrench on it. I was able to remove the bolt. I've heard of folks removing the pulley, something I did not want to get into!! I replaced it with a hex head bolt thinking maybe I will be able to get a regular box or open end wrench in there if I every have to do this again. Even with the pipe bolts removed, the pipe will not move sufficiently to get the pump off. There is a 2" or so hose attaching this pipe to the right side. It has been mentioned on the list that this hose could go, so I took that hose off for replacement. Then the pipe could be moved to the right enough to get the pump off. Had to be the most difficult pump R&R I've ever done.

I also replaced the large metal pipe going from the pump back to the thermostat housing. This pipe was ready to go. It had some rust "mounds" that when I poked them became pin-hole leaks real quick. Also there is a smaller diameter pipe off this one that rusts at the weld point, and it was ready to burst through there as well. I recommend replacing this pipe. It costs $70-80.

Good luck,

Kerry '86 syncro 167K kstanley@cas.org

-----Original Message----- From: Dennis Haynes [mailto:dhaynes57@EMAIL.MSN.COM] Sent: Sunday, May 23, 1999 9:27 PM To: vanagon@GERRY.VANAGON.COM Subject: Re: SOS: Waterpump Questions: Help!

A noisy water pump should always be replaced. When the bearings fail, the impeller will damage the engine case. This area will either have to be epoxied or welded to restore proper pump efficiency. having groves in the case causes loss of pump pressure. This can cause problems such as poor heat at idle, insufficient flow at low speeds or the radiator fan responding fast enough due to the poor radiator flow.

Dennis

-----Original Message----- From: Mark B. Magee <condor2@FLASH.NET> To: vanagon@GERRY.VANAGON.COM <vanagon@GERRY.VANAGON.COM> Date: Saturday, May 22, 1999 10:43 PM Subject: SOS: Waterpump Questions: Help!

>Volks, >The waterpump on my 91 Westy has the rather mild rattle beginning that >has me concerned. We are loaded for a 1200 mile trip to take off in the >morning. The water pump I have noticed to be noisy; when it's off you >can barely get any play a out of the pulley, yet there is a tiny amount. >No water is leaking. This Westy has 143K on it and records show a >waterpump at 55K. >Question, do I have 1500 miles on this waterpump! (Can I leave for >vacation!!!). As we are leaving on Sunday, we can't even get a pump on >our way out of Houston. >How long from the first tremblings of trouble until real trouble, eg. >excessive water leakage or bearing failure. >I can wait until Monday and do a pump then....... But I lose 2 days >camping with the family..... >I once nursed a 3/4 Suburban w/a leaking waterpump from El Paso to Kemah >(nearly 800 miles), pump leaked but I just kept topping off and replaced >when I got home. Mines not leaking and no excessive bearing freeplay, >presently. >I appreciate any thoughts or experience in this matter. Thanks > >-- >><> ><> ><> ><> ><> ><> ><> ><> ><> >Shalom 87 GL >Mark Magee 91 Westy >Kemah TX USA 96 Suzuki 4WD Sport >John 14:6


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.