Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (December 1999, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Tue, 30 Nov 1999 21:29:34 -0800
Reply-To:   David Marshall <vanagon@VOLKSWAGEN.ORG>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   David Marshall <vanagon@VOLKSWAGEN.ORG>
Subject:   Re: 4 Cyl VR-6 Conversion
Comments:   To: John Rodgers <inua@SCOTT.NET>
In-Reply-To:   <3844720B.C5E44D91@scott.net>
Content-Type:   text/plain; charset="us-ascii"

At 06:55 PM 30/11/1999 -0600, John Rodgers wrote: >Can anyone tell me about what goes into an engine swap using a 4 cyl >VR-6 engine.

First off, a VR6 is a 6 cylinder engine.

>Is this a desirable conversion?

Lots of power - 174hp, but you can eat transmissions if you use it all the time upon launch.

>Can it be mated to a standard 4 speed tranny.

Yes.

>Is an adapter plate required.?

Yes.

>Who makes one for this conversion?

I sell adapters that will work with the VR6

>Are diesel parts required?

Can't use the Diesel parts as the motor mounts are different, also there are slight differences in the flywheel.

>If so what? > >What about any other components needed. Additional engine supports, >exhaust system, mufflers, relocation of alternator, power steering >pumps, AC compressor, etc,etc.

We do not have a VR6 conversion kit per say - we just carry the flywheel that uses the vanagon clutch and pressure plate and the bellhousing adapter. The VR6 conversion kit will be ready when we have a customer who wants to be a guinea pig. The motor mounts are the part that will take us a few hours to figure out. The exhaust system can be made at the local muffler shop that custom bends pipes. You just have to make sure they design a STRONG bracket that prevents the exhaust system from vibrating at certain RPMs. I have pictures of the brackets that our exhaust guys use. The alternatior does not have to reloaced. The VR6 powersteering and AC pumps can drive the Vanagon components. You will have to get some hoses made up to extent everything a little as they are not in the same place as the Vanagons pumps are.

>Any input on this would be appreciated.

Personally I would not install a VR6 unless you have lots of time and patience to make it all work to your liking. A far simpler swap would be an inline four from a Golf or a Jetta. Please feel free to pmail me if you have any questions or visit my web site at http://www.fastforward.ca for a description and pricing of our inline conversion kit. > >John Rodgers >"88GL driver with a very dead wasserboxer. > >

-- David Marshall - - Quesnel, BC, Canada -- -- 78 VW Rabbit, 80 VW Caddy, 84 VW Westie, 85 VW Cabriolet -- -- 87 Audi 5000 Quattro, 88 2.0L VW Syncro Double Cab -- -- David's Volkswagen Home Page http://www.volkswagen.org -- -- Fast Forward Autobahn Sport Tuning http://www.fastforward.ca -- -- david@volkswagen.org (pmail) or vanagon@volkswagen.org (list) --


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.