Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2004, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 7 Apr 2004 12:55:03 -0400
Reply-To:     greg@POTTSFAMILY.CA
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Greg Potts <greg@POTTSFAMILY.CA>
Subject:      Re: noisy fuel pump
Comments: To: don spence <dspence@OANET.COM>
In-Reply-To:  <ED2D6F49-88AF-11D8-84BA-003065A72624@oanet.com>
Content-Type: text/plain; charset=ISO-8859-1

Hi Volks,

Rust in the tank is not the only possible source of contamination.

On our way to EveryBus 2002 our group gassed up at the Citgo in Depew N.Y. and two of the buses were at the side of the road within an hour due to plugged filters. My westfakia developed a vapour lock which was cleared by dis-assembling it, Dad's vanagon pump died outright and was replaced with a $100 ford pump and filter from a NAPA outlet in Bath N.Y.

Moral of the story: If the station is getting a refill from a tanker... find a different station. The refill can stir up sediment in their tank that winds up in your tank.

Happy trails,

Greg Potts Toronto, Ontario, Canada

1973/74/79 Westfakia Conversion **Bob the Tomato** LY3H 1977 Sunroof Automatic L63H/L90D http://www.pottsfamily.ca/westfakia http://www.geocities.com/busesofthecorn

Quoting don spence <dspence@OANET.COM>:

> > > > > > > > <<Suction screen in fuel tank is getting blocked with crud.>> > > > > True -but not always. I put a new tank in last year and my pump is > > noisy > > again. > > Just 2 days ago in Idaho I could'nt get past 40 mph. > > > > My engine began to lose power and stall as the noise increased . I > > reversed > > polarity of the pump momentarily and turned the key a few times. > > > > After reconnecting the wires correctly it started right up. > > I got all the power back and the noise went away. > > > > I suspect the pump brushes are worn. Since every pump I have as spares > > makes > > noise,so it's finally time for me to get a new pump. > > > > I took an old pump apart once and the commutator was deeply grooved > > from > > wear. > > Reversing the pump apparantely helps the brushed make better contact? > > > > Robert > > Not a chance Robert. Reversing the pump runs it backward pushing the > > crud out and clearing the inlet. Reconnecting allows it to pull gas > > through an unblocked or unrestricted inlet. (untilit gets blocked > > again) Time to clean out your tank and maybe apply a sealant.


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.